PCAN-USB FD
CAN FD Interface for High-Speed USB 2.0

PCAN-USB FD
IPEH-004022 € 245,00

All prices are plus the at present valid value added tax!

Description

The CAN FD adapter PCAN-USB FD allows the connection of CAN FD and CAN networks to a computer via USB. A galvanic isolation of up to 500 Volts decouples the PC from the CAN bus. The simple handling and its compact plastic casing make the adapter suitable for mobile applications.

The new CAN FD standard (CAN with Flexible Data rate) is primarily characterized by higher bandwidth for data transfer. The maximum of 64 data bytes per CAN FD frame (instead of 8 so far) can be transmitted with bit rates up to 12 Mbit/s. CAN FD is downward-compatible to the CAN 2.0 A/B standard, thus CAN FD nodes can be used in existing CAN networks. However, in this case the CAN FD extensions are not applicable.

The monitor software PCAN-View and the programming interface PCAN-Basic for the development of applications with CAN connection are included in the scope of supply and support the new standard CAN FD.

 

ISO / Non-ISO CAN FD:


Since the first implementations of CAN FD, the protocol has been improved and is now included in the standard ISO 11898-1. The revised CAN FD standard is not compatible with the original protocol.

PEAK-System takes this into account by supporting both protocol versions with their CAN FD interfaces. If required, the user can switch to the CAN FD protocol used in the environment by software („Non-ISO“ and „ISO“). Devices delivered until February 2015 need a firmware update for this functionality. If you are interested and for further information, please contact

 

 

Technical Specifications

Pin assignment D-Sub

Pin Pin assignment
1 not connected / optional +5V
2 CAN-L
3 GND
4 not connected
5 not connected
6 GND
7 CAN-H
8 not connected
9 not connected
  • Adapter for High-speed USB 2.0 (compatible to USB 1.1 and USB 3.0)
  • High-speed CAN connection (ISO 11898-2)
  • Complies with CAN specifications 2.0 A/B and FD
  • CAN FD support for ISO and Non-ISO standards switchable
  • CAN FD bit rates for the data field (64 bytes max.) from 25 kbit/s up to 12 Mbit/s
  • CAN bit rates from 25 kbit/s up to 1 Mbit/s
  • Time stamp resolution 1 μs
  • CAN bus connection via D-Sub, 9-pin
    (in accordance with CiA® 303-1)
  • FPGA implementation of the CAN FD controller
  • NXP TJA1044GT CAN transceiver
  • Galvanic isolation up to 500 V
  • CAN termination can be activated through a solder jumper
  • Measurement of bus load including error frames and overload frames on the physical bus
  • Induced error generation for incoming and outgoing CAN messages
  • 5-Volt supply to the CAN connection can be connected through a solder jumper, e.g. for external bus converter
  • Voltage supply via USB
  • Extended operating temperature range from -40 to 85 °C (-40 to 185 °F)

Scope of supply

  • PCAN-USB FD in plastic casing
  • Device drivers for Windows® 10, 8.1, 7 and Linux (32/64-bit)
  • CAN monitor PCAN-View for Windows® Details ...
  • Programming interface PCAN-Basic for developing applications with CAN connection Details ...
  • Programming interfaces for standardized protocols from the automotive sector
  • Manual in PDF format

Downloads

Device driver setup for Windows®

PEAK-System installation package for device drivers and tools for Windows® 10, 8.1, 7 (32/64-bit).

Device driver for Linux

Device drivers for PEAK CAN interfaces from Kernel 2.4 and higher.

PCAN-USB FD manual

PCAN-View

Windows® software for displaying, transmitting, and recording CAN and CAN FD messages

PCAN-Flash

Windows® software for flashing firmware via CAN

PCAN-Basic API

API for the development of applications with CAN and CAN FD connections for Windows® 10, 8.1, 7 (32/64-Bit)

PCAN-Basic API (Linux)

API for the development of applications with CAN connection for Linux

PCAN-CCP API

API for the development of software for the communication with ECUs according to the CAN Calibration Protocol (CCP)

PCAN-XCP API

API for the development of software for the communication with ECUs according to the Universal Measurement and Calibration Protocol (XCP)

PCAN-ISO-TP API

API for the transfer of data packages according to ISO-TP (ISO 15765-2)

PCAN-UDS API

API to communicate with control devices according to UDS (ISO 14229-1)

PCAN-OBD-2 API

API for the vehicle diagnostics according to OBD-2 (ISO 15765-4)

PCAN-PassThru API

Pass-Thru API and connection of Pass-Thru software to PEAK CAN interfaces. Installation for Windows® 10, 8.1, 7 (32/64-bit) includes interface DLLs, a configuration software, the PCAN-Basic API, and the PCAN-ISO-TP API. The download also contains the documentation (English).

More

Additional information on other pages:

PCAN-USB FD forum: Section for the PCAN-USB FD for question and support
The new standard CAN FD: support and compatible products
Device driver 4.x version history