|
BUS CONVERTER MODULE |
|
Connection to other CAN transceivers
|
 |
|
PCAN-TJA1054
The PCAN-bus converter (TJA1054) allows CAN high-speed components (based on the PCA82C250, PCA82C251 and TJA1050 transceivers by Philips), e.g. PCAN-USB or PCAN-PCI card, to be connected to the low-speed CAN-bus (PCA82C252, TJA1053, TJA1054). The 5V supply of the bus converter is established via PIN1 of the 9-pin Sub-D socket.
|
|
|
 |
|
|
|
|
| Specifications PCAN-TJA1054 |
- Adapter from high-speed CAN (PCA82C251) to low-speed CAN (TJA 1054). Transfer rates up to 125 kbit/s
- Philips PCA82C251 and TJA1054 CAN transceiver
- Termination resistors for low-speed CAN can be switched (560 / 5.66K)
- Power-LED
- Error LED (low-speed CAN)
- Connection via 9-pin Sub-D assignment according to CiA recommendation DS102
- All PEAK CAN cards can be set to the required supply via solder jumper
|
|
|
|
Pin assignment 9-pole connector female:
Connection side 82C251 (or 82C250)
|
|
Pin |
Configuration |
 |
|
1 |
5 V Power supply |
|
2 |
CAN-L |
|
3 |
GND |
|
4 |
Not connected |
|
5 |
Not connected |
|
6 |
GND |
|
7 |
CAN-H |
|
8 |
Not connected |
|
9 |
Not connected |
Pin assignment 9-pole connector male:
Connection side TJA 1054 |
|
Pin |
Configuration |
 |
|
1 |
Not connected |
|
2 |
CAN-L |
|
3 |
GND |
|
4 |
Not connected |
|
5 |
Not connected |
|
6 |
GND |
|
7 |
CAN-H |
|
8 |
Not connected |
|
9 |
Not connected |
|
|
|
|
|
|
|
PCAN-AU5790
The PCAN-AU5790 adapter is the interface between a high-speed CAN (HS-CAN) and a so-called single-wire CAN (SW-CAN). Basically, it can be used at any position of the HS-CAN. Primarily, however, it is designed for the direct connection of a HS-CAN hardware (e.g. PCAN-USB) to a SW-network.
|
|
|
 |
|
| Specifications PCAN-AU5790 |
- Three possible operating modes of the SW-CAN side (Normal / High-speed / Wake-up), adjustable via slide switch
- Indicator LEDs for power supply (red) and wake-up signals (yellow)
- Power supply (5 V) via PCAN adapter (no special power pack required), internal charge pump for nominal 12 V for supply of the SW-CAN transceiver
- Additional external power supply (12 V) for SW-CAN transceiver (e.g. by car battery) required only if the 5 V supply cannot provide enough power (min. 150 mA). This is the case, e.g. with all PEAK-CAN adapters with electrical isolation (optical decoupling).
|
|
|
| Pin assignment |
|
Pin |
Configuration |
|
|
1 |
not connected |
|
2 |
not connected |
|
3 |
Ground |
|
4 |
not connected |
|
5 |
CAN-H |
|
6 |
Ground |
|
7 |
not connected |
|
8 |
not connected |
|
9 |
Vaux (if necessary) |
|
|
|
|
|
|
|
PCAN-B10011S
The PCAN-B10011S bus converter establishes a connection between a high-speed CAN-node and a truck trailer CAN bus (ISO 11992-1).
|
|
|
 |
|
| Specifications PCAN-B10011S |
- Direct connection to an HS-CAN component (Sub-D socket, 9-pin)
- Switchable termination of the HS-CAN
- Connection of the Truck Trailer CAN via 9-pin Sub-D connector
- Choice of operating modes for the Truck Trailer CAN via slide switch
- Data transfer rates up to 125 kbit/s
- Power supply via Truck Trailer CAN-bus or self-sufficient with power supply unit
- Status display for power supply and error states via LEDs
|
|
|
| Pin assignment |
|
Pin |
Configuration |
|
|
1 |
not connected |
|
2 |
CAN-L |
|
3 |
Ground |
|
4 |
not connected |
|
5 |
not connected |
|
6 |
Ground |
|
7 |
CAN-H |
|
8 |
not connected |
|
9 |
Battery |
|
|
|
|
| Ordering information |
| Designation |
Art. No. |
| PCAN-TJA1054 |
IPEH-002039 |
| PCAN-AU5790 |
PEH-002040 |
| PCAN-B10011S |
PEH-002041 |
|
|
| Scope of supply |
- Adapter in plastic casing
- Manual
- Power supply unit (only PCAN-B10011S)
Other transceiver types on request
|
|
