We use cookies on our website to provide you with the best possible service and to further improve our website. By clicking the "Accept All" button, you agree to the use of all cookies. You can limit the cookies used by clicking on "Accept selection". Further information and an option to revoke your selection can be found in our privacy policy.


These cookies are necessary for basic functionality. This allows you to register on our website and forum or order products with our online shop.


With these cookies, we collect anonymized usage data for our website. For example, we can see which content is interesting for our visitors and which resolutions are used. We use the information to optimize our website to provide you with the best possible user experience.


show more

PCAN-MiniDiag FD

Compact Diagnostic Device for CAN and CAN FD Buses

PCAN-MiniDiag FD
IPEH-003070 € 295,00

All prices are plus the at present valid value added tax!

The PCAN-MiniDiag FD is a compact, low-cost handheld device for basic diagnosis and checking of CAN and CAN FD buses. Service technicians and developers can easily access networks of vehicles, machines, or industrial equipment whose configuration is unknown. For this, the nominal bit rate for CAN and additionally the data bit rate for CAN FD are determined using bit timing measurement. Furthermore, the device has measuring functions for the termination, bus load, and voltage levels at the CAN connector.

The PCAN-MiniDiag FD has an increased protection due to its membrane keypad and casing. The power is supplied by three replaceable batteries.

The CAN FD standard (CAN with Flexible Data rate) is primarily characterized by higher bandwidth for data transfer. The maximum of 64 data bytes per CAN FD frame (instead of 8 so far) can be transmitted with bit rates up to 10 Mbit/s. CAN FD is downward-compatible to the CAN 2.0 A/B standard, thus CAN FD nodes can be used in existing CAN networks. However, in this case the CAN FD extensions are not applicable.

  • High-speed CAN connection (ISO 11898-2)
    • Complies with CAN specifications 2.0 A/B and FD
    • CAN FD support for ISO and Non-ISO standards
    • CAN FD bit rates for the data field (64 bytes max.) from 66.6 kbit/s up to 10 Mbit/s
    • CAN bit rates from 10 kbit/s up to 1 Mbit/s
    • Microchip MCP2558FD CAN transceiver
  • CAN bus connection via D-Sub, 9-pin (in accordance with CiA® 106)
  • No influence on the CAN bus due to permanent listen-only mode
  • OLED display with 128 x 128 pixel resolution
  • Power supply via exchangeable batteries (3 x Micro AAA with 1.2 V or 1.5 V)
  • Operation via membrane keypad with four keys
  • Plastic casing with increased Ingress Protection IP42
  • Dimensions: 122 x 69 x 44 mm
  • Operating temperature range from -10 to +50 °C (14 to 122 °F)

Device and measuring functions

  • System Info: Indication of firmware and hardware version, serial number, and battery voltage
  • D-Sub Voltages: Voltage check at the pins 6 and 9 in the range from -40 to +43 V
  • CAN Min/Max: Measurement of minimum and maximum voltage values for CAN-High and CAN-Low in the range from -5 to +8 V
  • CAN Voltages: Measurement of dominant and recessive levels for CAN-High and CAN-Low in the range from -5 to +8 V
  • CAN Voltages 2: Measurement of minimum, mean, and maximum values of the dominant and recessive levels
  • Termination: Measurement of the termination on the CAN bus
  • Bit Rate: Automatic detection of bit rates via exact bit timing measurements or manual bit rate configuration
  • Bus Load: Measurement of the CAN bus load with display in diagram
  • Statistics: Counter for CAN, CAN FD, and error frames
  • PCAN-MiniDiag FD in plastic casing
  • Batteries (4 x 1.5 V Micro AAA)
  • Manual in PDF format
  • Printed quick start guide

PCAN-MiniDiag FD manual

German English

PCAN-MiniDiag FD quick start

German English

PEAK-Flash 2

Easy-to-use tool for updating the firmware of PEAK-System hardware products as well as CAN and LIN adapters for Windows® 11 (x64/ARM64), 10 (x64).


Additional information