We use cookies on our website to provide you with the best possible service and to further improve our website. By clicking the "Accept All" button, you agree to the use of all cookies. You can limit the cookies used by clicking on "Accept selection". Further information and an option to revoke your selection can be found in our privacy policy.

Necessary:

These cookies are necessary for basic functionality. This allows you to register on our website and forum or order products with our online shop.

Statistics:

With these cookies, we collect anonymized usage data for our website. For example, we can see which content is interesting for our visitors and which resolutions are used. We use the information to optimize our website to provide you with the best possible user experience.

Necessary
Statistics

show more

PCAN-PCI/104-Express FD

CAN and CAN FD Interface for PCI/104-Express

PCAN-PCI/104-Express FD Single Channel
IPEH-004080 € 295,00
PCAN-PCI/104-Express FD Dual Channel
IPEH-004081 € 375,00
PCAN-PCI/104-Express FD Four Channel
IPEH-004082 € 470,00

All prices are plus the at present valid value added tax!

The PCAN-PCI/104-Express FD allows the connection of PCI/104-Express systems to CAN and CAN FD buses. The PCI/104-Express specification establishes PCI Express for the PC/104 form factor wherewith up to four cards can be stacked. Based on this, standardized modular embedded systems such as industrial PCs can be realized. The CAN bus is connected via 9-pin D-Sub connectors to the supplied slot brackets. There is a galvanic isolation between the computer and the CAN side up to 500 Volts. The card is available as a single, dual, or four-channel version.

The CAN FD standard (CAN with Flexible Data rate) is primarily characterized by higher bandwidth for data transfer. The maximum of 64 data bytes per CAN FD frame (instead of 8 so far) can be transmitted with bit rates up to 12 Mbit/s. CAN FD is downward-compatible to the CAN 2.0 A/B standard, thus CAN FD nodes can be used in existing CAN networks. However, in this case the CAN FD extensions are not applicable.

The monitor software PCAN-View and the programming interface PCAN-Basic for the development of applications with CAN connection are included in the scope of supply and support the standard CAN FD.

ISO / Non-ISO CAN FD


Since the first implementations of CAN FD, the protocol has been improved and is now included in the standard ISO 11898-1. The revised CAN FD standard is not compatible with the original protocol.

PEAK-System takes this into account by supporting both protocol versions with their CAN FD interfaces. If required, the user can switch to the CAN FD protocol used in the environment by software („Non-ISO“ and „ISO“). Devices delivered until February 2015 need a firmware update for this functionality. If you are interested and for further information, please contact

Pin assignment D-Sub

1 Not connected / optional +5 V
2 CAN-L
3 GND
6 GND
7 CAN-H
  • PCI/104-Express card, 1 lane (x1)
  • Form factor PC/104
  • Up to four cards can be used in one system
  • 1, 2, or 4 High-speed CAN channels (ISO 11898-2)
  • Complies with CAN specifications 2.0 A/B and FD
  • CAN FD support for ISO and Non-ISO standards switchable
  • CAN FD bit rates for the data field (64 bytes max.) from 20 kbit/s up to 12 Mbit/s
  • CAN bit rates from 20 kbit/s up to 1 Mbit/s
  • Connection to CAN bus through D-Sub slot bracket, 9-pin (in accordance with CiA® 106)
  • FPGA implementation of the CAN FD controller
  • Microchip CAN transceiver MCP2558FD
  • Galvanic isolation on the CAN connection up to 500 V, separate for each CAN channel
  • CAN termination can be activated through solder jumpers, separately for each CAN channel
  • 5-Volt supply to the CAN connection can be connected through a solder jumper, e.g., for external bus converter
  • PCIe data transfer via bus master DMA
  • DMA memory access operations with 32- and 64-bit addresses
  • Measurement of bus load including error frames and overload frames on the physical bus
  • Induced error generation for incoming and outgoing CAN messages
  • Optionally available: PCI-104 stack-through connector
  • Extended operating temperature range from -40 to +85 °C (-40 to +185 °F)
  • PCAN-PCI/104-Express FD card
  • Slot bracket with D-Sub connector(s) for the CAN bus (two for the four-channel version)
  • Device drivers for Windows® 11 (x64), 10 (x64), and Linux
  • CAN monitor PCAN-View for Windows® Details ...
  • Programming interface PCAN-Basic for developing applications with CAN connection Details ...
  • Programming interfaces for standardized protocols from the automotive sector
  • Manual in PDF format

Device driver setup for Windows

PEAK-System installation package for PC interface device drivers for Windows® 11 (x64/ARM64), 10 (x64). Included tools: PEAK Settings, PCAN-View, PLIN-View Pro, and Virtual PCAN-Gateway. Included APIs: PCAN-Basic, PLIN-API, and PCAN-RP1210.

Download

Device driver for Linux

Device drivers for PEAK CAN interfaces running on Kernel 2.6 and higher.

Website

PCAN-PC/104-Express FD manual

German English

PCAN-View

Software for displaying, transmitting, and recording CAN and CAN FD messages for Windows® 11 (x64/ARM64), 10 (x86/x64).

Please note: PCAN-View is a part of our device driver setup.

Download

PEAK-Flash 2

Easy-to-use tool for updating the firmware of PEAK-System hardware products as well as CAN and LIN adapters for Windows® 11 (x64/ARM64), 10 (x64).

Download

PCAN-Basic API

API for the development of applications with CAN and CAN FD connections for Windows® 11 (x64/ARM64), 10 (x64).

Download

PCAN-Basic API (Linux)

API for the development of applications with CAN connection for Linux.

Download

PCAN-Basic.NET Assembly

The PCAN-Basic.NET Assembly is available as a package in the NuGet Gallery. The online documentation is available on our website.

Documentation NuGet Gallery

PCAN-CCP API

API for the development of software for the communication with ECUs according to the CAN Calibration Protocol (CCP) for Windows® 11 (x64/ARM64), 10 (x86/x64).

Download

PCAN-XCP API

API for the development of software for the communication with ECUs according to the Universal Measurement and Calibration Protocol (XCP) for Windows® 11 (x64/ARM64), 10 (x86/x64).

Download

PCAN-ISO-TP API

API for the transfer of data packages according to ISO-TP (ISO 15765-2) for Windows® 11 (x64/ARM64), 10 (x64).

Download

PCAN-UDS API

API to communicate with control devices according to UDS (ISO 14229-1) for Windows® 11 (x64/ARM64), 10 (x64).

Download

PCAN-OBD-2 API

API for the vehicle diagnostics according to OBD-2 (ISO 15765-4) for Windows® 11 (x64/ARM64), 10 (x64).

Download

PCAN-PassThru API

Pass-Thru API and connection of Pass-Thru software to PEAK CAN interfaces. Installation for Windows® 11 (x64/ARM64), 10 (x64) includes interface DLLs, a configuration software, and the PCAN-ISO-TP API. The download also contains the documentation (English).

Download

Additional information