PCAN-PCI Express FD
CAN FD Interface for PCI Express

PCAN-PCI Express FD Single Channel
IPEH-004026 € 240,00
PCAN-PCI Express FD Dual Channel
IPEH-004027 € 300,00
PCAN-PCI Express FD Four Channel
IPEH-004040 € 350,00

All prices are plus the at present valid value added tax!

Description

The plug-in card PCAN-PCI Express FD allows the connection of a PC with PCI Express slots to CAN FD and CAN networks. There is galvanic isolation of up to 500 Volts between the computer and CAN sides. The card is available as a single, dual, or four-channel version.

The new CAN FD standard (CAN with Flexible Data rate) is primarily characterized by higher bandwidth for data transfer. The maximum of 64 data bytes per CAN FD frame (instead of 8 so far) can be transmitted with bit rates up to 12 Mbit/s. CAN FD is downward-compatible to the CAN 2.0 A/B standard, thus CAN FD nodes can be used in existing CAN networks. However, in this case the CAN FD extensions are not applicable.

The monitor software PCAN-View and the programming interface PCAN-Basic for the development of applications with CAN connection are included in the scope of supply and support the new standard CAN FD.

 

ISO / Non-ISO CAN FD:


Since the first implementations of CAN FD, the protocol has been improved and is now included in the standard ISO 11898-1. The revised CAN FD standard is not compatible with the original protocol.

PEAK-System takes this into account by supporting both protocol versions with their CAN FD interfaces. If required, the user can switch to the CAN FD protocol used in the environment by software („Non-ISO“ and „ISO“). Devices delivered until February 2015 need a firmware update for this functionality. If you are interested and for further information, please contact

 

 

Technical Specifications

Pin assignment D-Sub

Pin Pin assignment
1 not connected / optional +5V
2 CAN-L
3 GND
4 not connected
5 not connected
6 GND
7 CAN-H
8 not connected
9 not connected
  • PC plug-in card (PCIe x1) for PCI Express slots
  • 1, 2, or 4 High-speed CAN channels
    (ISO 11898-2)
  • Complies with CAN specifications 2.0 A/B and FD
  • CAN FD support for ISO and Non-ISO standards switchable
  • CAN FD bit rates for the data field (64 bytes max.) from 25 kbit/s up to 12 Mbit/s
  • CAN bit rates from 25 kbit/s up to 1 Mbit/s
  • CAN bus connection via D-Sub, 9-pin
    (in accordance with CiA® 303-1)
  • FPGA implementation of the CAN FD controller
  • NXP TJA1044GT CAN transceiver
  • Galvanic isolation on the CAN connection up to
    500 V, separate for each CAN channel
  • CAN termination can be activated through a solder jumper, separately for each CAN channel
  • PCIe data transfer via bus master DMA
  • DMA memory access operations with 32- and 64-bit addresses
  • Measurement of bus load including error frames and overload frames on the physical bus
  • Induced error generation for incoming and outgoing CAN messages
  • 5-Volt supply to the CAN connection can be connected through a solder jumper, e.g. for external bus converter
  • Extended operating temperature range from -40 to 85 °C (-40 to 185 °F)

 

 

 

Scope of Supply

  • Plug-in card PCAN-PCI Express FD
  • Slot bracket with D-Sub connectors for the CAN bus (only four-channel version)
  • Device drivers for Windows® 10, 8.1, 7 and Linux (32/64-bit)
  • CAN monitor PCAN-View for Windows® Details ...
  • Programming interface PCAN-Basic for developing applications with CAN connection Details ...
  • Programming interfaces for standardized protocols from the automotive sector
  • Manual in PDF format

 

 

Downloads

Device driver setup for Windows

PEAK-System installation package for device drivers and tools for Windows® 10, 8.1, 7 (32/64-bit) for our PC interfaces.

Device driver for Linux

Device drivers for PEAK CAN interfaces from Kernel 2.4 and higher.

PCAN-PCI Express FD manual

PCAN-View

Windows® software for displaying, transmitting, and recording CAN and CAN FD messages

PCAN-Basic API

API for the development of applications with CAN and CAN FD connections for Windows® 10, 8.1, 7 (32/64-Bit)

PCAN-Basic API (Linux)

API for the development of applications with CAN connection for Linux

PCAN-CCP API

API for the development of software for the communication with ECUs according to the CAN Calibration Protocol (CCP)

PCAN-XCP API

API for the development of software for the communication with ECUs according to the Universal Measurement and Calibration Protocol (XCP)

PCAN-ISO-TP API

API for the transfer of data packages according to ISO-TP (ISO 15765-2)

PCAN-UDS API

API to communicate with control devices according to UDS (ISO 14229-1)

PCAN-OBD-2 API

API for the vehicle diagnostics according to OBD-2 (ISO 15765-4)

PCAN-PassThru API

Pass-Thru API and connection of Pass-Thru software to PEAK CAN interfaces. Installation for Windows® 10, 8.1, 7 (32/64-bit) includes interface DLLs, a configuration software, the PCAN-Basic API, and the PCAN-ISO-TP API. The download also contains the documentation (English).

BaudTool

Windows® software for calculating the BTR0/BTR1 baud rate register

More

Additional information on other pages:

PCAN-PCI Express FD forum: Section for the PCAN-PCI Express FD card for question and support
The new standard CAN FD: support and compatible products
CAN device driver 4.x version history