This website uses cookies for analytics, for logins to the online shop and the forum, and for the handling of an order. By browsing this website you agree to the use of cookies. Detailed information on their use can be found in our privacy policy.

OK Privacy Policy

PCAN-PCI/104-Express FD

CAN FD Interface for PCI/104-Express

PCAN-PCI/104-Express FD Single Channel
IPEH-004080 € 290,00
PCAN-PCI/104-Express FD Dual Channel
IPEH-004081 € 370,00
PCAN-PCI/104-Express FD Four Channel
IPEH-004082 € 460,00

All prices are plus the at present valid value added tax!

The PCAN-PCI/104-Express FD allows the connection of PCI/104-Express systems to CAN and CAN FD busses. The PCI/104-Express specification establishes PCI Express for the PC/104 form factor wherewith up to four cards can be stacked. Based on this, standardized modular embedded systems such as industrial PCs can be realized. The CAN bus is connected via 9-pin D-Sub connectors to the supplied slot brackets. There is a galvanic isolation between the computer and the CAN side up to 500 Volts. The card is available as a single, dual, or four-channel version.

The new CAN FD standard (CAN with Flexible Data rate) is primarily characterized by higher bandwidth for data transfer. The maximum of 64 data bytes per CAN FD frame (instead of 8 so far) can be transmitted with bit rates up to 12 Mbit/s. CAN FD is downward-compatible to the CAN 2.0 A/B standard, thus CAN FD nodes can be used in existing CAN networks. However, in this case the CAN FD extensions are not applicable.

The monitor software PCAN-View and the programming interface PCAN-Basic for the development of applications with CAN connection are included in the scope of supply and support the new standard CAN FD.

ISO / Non-ISO CAN FD:


Since the first implementations of CAN FD, the protocol has been improved and is now included in the standard ISO 11898-1. The revised CAN FD standard is not compatible with the original protocol.

PEAK-System takes this into account by supporting both protocol versions with their CAN FD interfaces. If required, the user can switch to the CAN FD protocol used in the environment by software („Non-ISO“ and „ISO“). Devices delivered until February 2015 need a firmware update for this functionality. If you are interested and for further information, please contact

 

 

Pin assignment D-Sub

Pin Pin assignment
1 Not connected / optional +5V
2 CAN-L
3 GND
4 Not connected
5 Not connected
6 GND
7 CAN-H
8 Not connected
9 Not connected
  • PCI/104-Express card, 1 lane (x1)
  • Form factor PC/104
  • Up to four cards can be used in one system
  • 1, 2, or 4 High-speed CAN channels (ISO 11898-2)
  • Complies with CAN specifications 2.0 A/B and FD
  • CAN FD support for ISO and Non-ISO standards switchable
  • CAN FD bit rates for the data field (64 bytes max.) from 20 kbit/s up to 12 Mbit/s
  • CAN bit rates from 20 kbit/s up to 1 Mbit/s
  • Connection to CAN bus through D-Sub slot bracket, 9-pin (in accordance with CiA® 303-1)
  • FPGA implementation of the CAN FD controller
  • Microchip CAN transceiver MCP2558FD
  • MCP2558FD CAN transceiver
  • Galvanic isolation on the CAN connection up to 500 V, separate for each CAN channel
  • CAN termination can be activated through a solder jumper, separately for each CAN channel
  • 5-Volt supply to the CAN connection can be connected through a solder jumper, e.g. for external bus converter
  • PCIe data transfer via bus master DMA
  • DMA memory access operations with 32- and 64-bit addresses
  • Measurement of bus load including error frames and overload frames on the physical bus
  • Induced error generation for incoming and outgoing CAN messages
  • Optionally available: PCI-104 stack-through connector
  • Extended operating temperature range from -40 to 85 °C (-40 to 185 °F)

 

 

  • PCAN-PCI/104-Express FD card
  • Slot bracket with D-Sub connector(s) for the CAN bus (two for the four-channel version)
  • Device drivers for Windows® 10, 8.1, 7 and Linux (32/64-Bit)
  • CAN monitor PCAN-View for Windows® Details ...
  • Programming interface PCAN-Basic for developing applications with CAN connection Details ...
  • Programming interfaces for standardized protocols from the automotive sector
  • Manual in PDF format

Device driver setup for Windows

Download

PEAK-System installation package for device drivers and tools for Windows® 10, 8.1, 7 (32/64-bit) for our PC interfaces.

Device driver for Linux

Website

Device drivers for PEAK CAN interfaces from Kernel 2.4 and higher.

PCAN-PC/104-Express FD manual

German English

PCAN-View

Download

Windows® software for displaying, transmitting, and recording CAN and CAN FD messages.

PCAN-Basic API

Download

API for the development of applications with CAN and CAN FD connections for Windows® 10, 8.1, 7 (32/64-Bit)

PCAN-Basic API (Linux)

Download

API for the development of applications with CAN connection for Linux

PCAN-CCP API

Download

API for the development of software for the communication with ECUs according to the CAN Calibration Protocol (CCP)

PCAN-XCP API

Download

API for the development of software for the communication with ECUs according to the Universal Measurement and Calibration Protocol (XCP)

PCAN-ISO-TP API

Download

API for the transfer of data packages according to ISO-TP (ISO 15765-2)

PCAN-UDS API

Download

API to communicate with control devices according to UDS (ISO 14229-1)

PCAN-OBD-2 API

Download

API for the vehicle diagnostics according to OBD-2 (ISO 15765-4)

PCAN-PassThru API

Download

Pass-Thru API and connection of Pass-Thru software to PEAK CAN interfaces. Installation for Windows® 10, 8.1, 7 (32/64-bit) includes interface DLLs, a configuration software, the PCAN-Basic API, and the PCAN-ISO-TP API. The download also contains the documentation (English).

Additional information on other pages:

PCAN-PCI/104-Express FD forum: Section for the PCAN-PCI/104-Express FD card for question and support
The new standard CAN FD: support and compatible products
CAN device driver 4.x version history